Equipment

Good Survivalist has Tools and Experience

You can get out of dodge to survive catastrophic events.

If you do not have air conditioning or it needs repaired you can DIY.

Connect the conduit

 

 

repair the electronics

 

 

 

Install air flow parts

 

 

DIY A/C repair tasks

  • A dirty air filter can reduce the efficiency of your A/C and cause it to struggle to cool your home. Check the filter every month and either clean or replace it as needed.
  • Inspect the thermostat: Ensure that your thermostat is set to “cool” and that the temperature is set lower than the current room temperature. If your thermostat is battery-operated, check the batteries and replace them if necessary. A malfunctioning thermostat might need to be replaced by a professional.
  • Check the circuit breaker: If your A/C isn’t turning on, it’s possible that the circuit breaker has tripped. Locate your electrical panel and check the breaker for your air conditioning system. If it’s in the “off” position, reset it by flipping it back to the “on” position.
  • Clean the outdoor condenser unit: The outdoor condenser unit can become clogged with dirt, leaves, and other debris, reducing the efficiency of your A/C system. Turn off the power to your air conditioner, then carefully clean the condenser coils and fins using a soft brush or garden hose with a gentle spray.
  • Inspect the condensate drain: A clogged condensate drain can cause water to back up and potentially damage your A/C system. Check the drain for any blockages and clear them if necessary.
  • Check for air leaks: Air leaks in your ductwork or around windows and doors can cause your A/C to work harder than necessary. Inspect your home for air leaks and seal them with weatherstripping or caulk.

 

Take part and reassemble

I’ll never forget the sweltering summer day when my air conditioner decided to give up on me. The timing couldn’t have been worse; the mercury was pushing past 90 degrees, and the humidity made the air feel like a wet blanket. I was determined not to let this machine defeat me, so I rolled up my sleeves and decided to take on the repair myself.

Armed with a sense of determination and a basic understanding of HVAC systems from previous DIY adventures, I gathered my tools. I had a multimeter that was essential for diagnosing electrical issues, a set of insulated screwdrivers specifically for electrical work, needle-nose pliers that were perfect for reaching into tight spaces, and an adjustable wrench for loosening and tightening nuts and bolts. The capacitor, which I suspected was the culprit, would need to be handled carefully, as it could still hold a charge even after the power was disconnected.

I approached the unit, a hulking metal box about 3 feet in height and 2 feet in width, its surface hot to the touch from the relentless sun. I switched off the circuit breaker to ensure safety — rule number one when working with electrical appliances. With my multimeter in hand, I carefully removed the access panel, which revealed the intricate maze of wires and components inside.

The inside of the unit was a bit intimidating, with its tangle of copper wires and shiny components all packed into the confined space. I took a deep breath and reminded myself to take it one step at a time. Following the schematic on the inside of the panel, I traced the wires to the capacitor, a cylindrical part about the size of a soda can with two sets of terminals on top.

Using my multimeter, I confirmed that the capacitor was indeed failing to hold a charge. I carefully discharged any remaining energy using the insulated screwdriver, bridging the terminals as I had learned from a trusted repair video. With the faulty part safely removed, I took a quick trip to the local hardware store to find a replacement, matching the specs exactly: 35 microfarads (μF) for the compressor and 5 μF for the fan motor, with a voltage rating of 370.

Back at home, I installed the new capacitor, double-checking every connection against the wiring diagram. I resecured the access panel, flipped the circuit breaker back on, and held my breath as I turned on the air conditioner.

 

Do it yourself tools list. You can build almost anything with these.

  1. Hammer
  2. Screwdriver (flathead and Phillips)
  3. Pliers (needle-nose, locking, and standard)
  4. Wrench (adjustable and socket)
  5. Tape measure
  6. Level
  7. Utility knife
  8. Handsaw
  9. Power drill
  10. Drill bits
  11. Screwdriver bits
  12. Chisels
  13. Wood plane
  14. Clamps (bar and spring)
  15. Sandpaper
  16. Paintbrushes
  17. Putty knife
  18. Stud finder
  19. Square
  20. T-square
  21. Speed square
  22. Pry bar
  23. Crowbar
  24. Sledgehammer
  25. Circular saw
  26. Jigsaw
  27. Miter saw
  28. Table saw
  29. Belt sander
  30. Orbital sander
  31. Router
  32. Wood glue
  33. Caulk gun
  34. Silicone caulk
  35. Construction adhesive
  36. Safety glasses
  37. Dust mask
  38. Work gloves
  39. Earplugs

 

Swamp cooler can save money

 

program the temp you want

overhead air conditioning systems are a pain to reach

 

 

 

a good set of tools is needed

Assortment of tools you will need

 

 

 

 

Get the pressure just right

DIY solar panels create electrical energy

Wilderness survival weapons

Water filters

Make a fire to stay warm and cook food

List of items you need infographic

Needed items:

  • 5 gallon bucket
  • Paracord
  • Dehydrator
  • Booby traps
  • Hand crank radio
  • GPS device
  • First aid kit
  • Water filter
  • Matches
  • Knife

 

eat lizards if you must

 

 

 

get a gas mask

multi tools in one

Be prepared emergency preparation checklist

 

 

drink fresh water from leaves

 

 

 

Have a knife and compass

 

 

FAQ

Q: What are some essential DIY tools for beginners? A: Ah, the magical world of DIY! Some essential tools for beginners include a hammer, screwdriver set, tape measure, adjustable wrench, and a trusty level. With these tools, you’ll be ready to tackle those home improvement projects like a DIY pro.

Q: Can I use duct tape for everything? A: Ah, the wonders of duct tape! While it may seem like a superhero of the DIY world, it’s not a cure-all solution. It’s perfect for temporary fixes, but remember, it’s not a magical spell that can fix everything from leaky pipes to broken hearts.

Q: Should I buy power tools or stick to hand tools? A: Power tools can make your DIY adventures more efficient and fun. But be warned, they can also turn you into a temporary rock star with their noise level. Just don’t mistake your workshop for a sold-out concert.

Q: How do I know which screwdriver head to use? A: It’s like a puzzle game with a twist! Match the screw head to the corresponding screwdriver bit: flathead for slotted screws, Phillips for cross-head screws, and Torx for those star-shaped screws. Just remember, “one size fits all” does not apply here.

Q: Can I use a hairdryer instead of a heat gun? A: While they may both blow hot air, a hairdryer is not a substitute for a heat gun. You don’t want to end up with a DIY disaster and a hairdo that looks like you just walked through a hurricane.

Q: Is it necessary to wear safety goggles and gloves? A: Safety first, my friend! Protecting your eyes and hands is always a good idea. DIY projects should be an adventure, not a trip to the emergency room. Let’s avoid any unplanned visits to the local medical professionals.

Q: What’s the secret to using a tape measure correctly? A: Ah, the art of measuring! The secret is to pull the tape measure out smoothly and hold it taut. Oh, and avoid letting it snap back and give you a delightful tap on the wrist. Measurements shouldn’t come with a side of surprise.

Q: Can I fix everything myself with DIY tools? A: Ah, the dreams of DIY dominance! While DIY tools are handy, some projects might be better left to the professionals. Remember, a little self-awareness can save you from a lot of DIY disasters.